Guangzhou, China · Smart Manufacturing Solutions [email protected] / +86 20 3337 2844

Industrial Manufacturing

On a factory floor the identification problem changes at every station: a paper label that works at goods-in may be unreadable after a wash, a serial number printed on a carton says nothing about the part inside it, and a part marked with a sticker loses that sticker in the first machining operation. This page covers the marking, labeling and scanning combinations MAISUI supplies for industrial manufacturing.

Where identification has to survive

  • Work in progress. Job cards, route tags and bin labels that travel with the batch through several operations, each of which may involve oil, coolant or heat.
  • Part marking. Serial numbers and lot codes applied directly to the part – laser-marked, dot-peen or engraved – where a label would be removed, painted over or burned away.
  • Finished goods. Nameplate labels, rating labels and compliance marks on the product itself, often specified by the customer or by a safety standard.
  • Packaging and shipping. Carton labels, pallet labels and packing lists produced at dispatch.
  • Tooling and fixtures. Asset tags, calibration labels and storage location labels that must remain legible for the life of the tool rather than the life of the order.

What the mark has to survive

Condition Pressure on the mark Typical direction
Cutting fluid and coolant Label adhesive softens, print dissolves Direct part marking, or resin ribbon on a synthetic label
Wash and degrease Solvent attacks ink and adhesive Laser or dot-peen mark; solvent-resistant label construction
High temperature Label yellows, adhesive fails High-temperature label stock; verify the actual peak temperature and dwell
Abrasion and handling Print wears off before the part is inspected Top-coated label with resin ribbon; or permanent direct mark
Years in service Nameplate becomes unreadable for service or warranty Etched or laser-marked plate rather than a printed sticker

Matching the marking method to the part

The first question is not which printer to buy but whether the mark has to live on the part or on a label attached to it. If the part is machined after marking, is shot-blasted, painted or goes through a heat treatment, only a direct mark survives. If the part is finished and boxed, a label is usually cheaper and easier to change.

  • Laser marking for permanent marks on metal and some plastics, with no consumable per mark – the LINX SL3 covers the common industrial marking range.
  • CIJ where the mark goes onto a part or a package at speed and the surface can accept ink – the LINX 8300.
  • TTO where a flexible package, tube or sachet needs a lot and date code on the seal – the SmartDate X45 is the usual fit for mid-range line speeds.
  • Thermal transfer printers for labels, job cards and shipping documents – the Q420 / Q430 / Q460 for high duty, desktop models for the office side.
  • DPM-capable scanners where the code is marked directly on metal – a standard imager reads a printed label but struggles with a low-contrast dot-peen mark. The MS-9566AI is specified for this case.

Consumables decide the result

Industrial label failure usually traces back to a ribbon and face stock chosen for print quality rather than for the environment. Resin ribbon on a top-coated synthetic label is the starting point for anything that sees solvent, abrasion or heat; wax-resin on coated paper covers indoor job cards and shelf labels. High-temperature labels need the peak temperature and dwell time confirmed, because a label rated for a short excursion behaves differently from one that sits in an oven for an hour.

Common mistakes

  • Marking a part with a label that is removed in the next operation, then re-labeling by hand and losing the trace to the original lot.
  • Buying a standard 2D imager for laser-marked metal and concluding that “the code cannot be read” when the scanner is the limitation.
  • Choosing a high-temperature label from a catalogue without testing it on the actual line.
  • Letting every station print its own label format, so the same part carries three different identifiers by the time it ships.

How a project runs

  1. Walk the route. We map each station the part passes and what the identifier has to survive at each one.
  2. Decide mark or label. Part marking where the label cannot survive, labels where it can – and the split is usually obvious after the route walk.
  3. Test on real parts. Marking and scanning tested on your material, not on a sample coupon.
  4. Standardise the data. One code structure across stations, tied to the MES or ERP record that already holds the work order.

Standardising identifiers across stations

A plant rarely has one identification problem; it has as many as it has stations, and each station historically solved its own. The result is a part that carries a job card number at cutting, a serial number at assembly and a different lot code at packing, with no key that ties the three together. When a customer or an auditor asks which heat of material went into a delivered unit, the answer has to be assembled by hand.

The fix is organisational before it is technical. One identifier structure – usually a work order number plus a part serial – carried by every station’s label or mark, and the same structure stored in the MES or ERP record. Once that is agreed, the equipment choice at each station only has to reproduce an existing identifier rather than invent a local one, which removes most of the integration work that otherwise falls on the last project.

For plants already running an MES, this is where the MES smart manufacturing system and the marking equipment meet: the station prints what the system already knows, and the scanning at each station writes back to the same record.

FAQ

Can a laser mark replace a label completely?

On machined, cast or stamped metal parts, usually yes, and it is the more durable option. On painted, coated or heat-treated surfaces the mark may be too low-contrast to scan, and on many plastics the wrong laser wavelength changes the material rather than marking it. We test on the actual part before recommending it.

What is DPM and why does it need a special scanner?

Direct part marking puts the code into the material rather than onto a label. The resulting contrast is often much lower than a printed label, and the surface may be curved or reflective. A DPM-capable scanner uses different lighting and decoding, which is why a phone camera or a paper-label imager often fails on the same mark.

Do you supply job cards and route tags as well as product labels?

Yes – job cards, route tags, bin labels and nameplates are all label work on the same printers. The important part is that the template and the ribbon grade are consistent across the stations, otherwise the same job card prints differently at two ends of the plant.

Can the marking be linked to our MES or ERP?

Yes. MAISUI also supplies MES and ERP software, so the serial or lot number printed at the station can be the same identifier the system already tracks. See the MES page and the ERP page for scope.