Guangzhou, China · Smart Manufacturing Solutions [email protected] / +86 20 3337 2844

Pharma & Healthcare

Pharmaceutical and medical device labeling is judged by an auditor rather than by a customer: the code has to be correct, legible, traceable to the batch and linked to a serial number that can be verified years later. The equipment is only one part of that chain – the label construction, the data and the verification step carry equal weight. This page covers what MAISUI supplies for pharma and healthcare producers.

Where the marked information has to work

  • Primary and secondary packs. Batch, expiry and serial numbers on cartons, bottles, vials and blisters, often at high line speed.
  • Unique device identification. UDI carriers on medical devices – a 2D code plus human-readable data, required in the EU under MDR and in the US under the FDA UDI rule.
  • Tamper evidence. Security labels and seals that show whether a pack has been opened, and that cannot be moved to another pack.
  • Cold chain and transport. Labels on secondary packaging and shippers that stay readable through chilled transport and, in some cases, through freezing.
  • Sterile barrier and reprocessing. Labels that survive sterilisation processes such as ethylene oxide or gamma, where many standard adhesives fail.

What the label has to survive

Condition Pressure on the label Typical direction
Sterilisation Adhesive or print degrades Sterilisation-compatible label and ribbon, verified on the real cycle
Cold chain Adhesive releases on cold, wet packs Cold-temperature adhesive with a suitable face stock
Solvents and disinfectants Print smears on handling Resin ribbon on a chemical-resistant synthetic label
Small vials and ampoules No room for the code Higher resolution print and a carrier sized to the container
Audit and retention Record must be reproduced years later Serial number linked to a retained production record, not just a printed code

Regulation shapes the data, the equipment follows

Three regimes set most of the requirements. The EU Falsified Medicines Directive requires a unique identifier and a tamper-evident seal on prescription medicines. The US Drug Supply Chain Security Act requires serialised product and transaction records. Medical devices carry UDI under the EU MDR and the FDA UDI rule. In each case the regulation defines what the code must contain and how it must be verifiable; the printer, ribbon and label only have to reproduce that content reliably and legibly.

That distinction matters when a producer asks for “a GMP printer”. No printer is compliant by itself. What can be shown to an auditor is that the code is produced consistently, verified after printing, and linked to a batch record. The equipment choice supports that chain; it does not replace it.

Matching equipment to the job

  • TTO for blister cards, sachets and pouches where the code goes onto the packaging material – the SmartDate X30 and X65 cover the common speed and width ranges.
  • CIJ for bottles, caps and vials where the code is applied to a curved surface – the LINX 8300.
  • Thermal transfer label printers for carton, shipper and UDI labels, with verification scanning immediately after printing.
  • Security and tamper-evident labels where the pack has to show evidence of opening or substitution.
  • Serialisation and traceability software where the requirement is one code per unit rather than one code per batch – see the MS7 one-item-one-code system.

Verification is part of the line, not an afterthought

A pharma line that prints a serial number but does not verify it is relying on the printer being right every time. In practice, verification means a scanner positioned after the print station that reads the code, checks it against the expected record and rejects or alerts on a failed read. The scanner has to be chosen for the same reason as the printer: a code that is dense, small and printed on a curved surface is exactly the case where a general-purpose handheld is too slow and too variable.

Where the volume does not justify an inline verifier, a manual verification step with a fixed scanner at the packing bench is the minimum, and the results should be recorded rather than observed.

Consumables decide the result

For healthcare labels the consumable is part of the validation. A resin ribbon on a synthetic label is the usual starting point for anything that meets solvent, abrasion or a sterilisation cycle, but the specific combination has to be tested on the real pack and the real process. Low-migration ink and adhesive apply where the label contacts the product or the patient. Labels that go through an autoclave or a gamma cycle need the cycle parameters confirmed before a label is specified, because a catalogue rating is not the same as a validated result.

Common mistakes

  • Specifying a label for room temperature and discovering the adhesive fails after a sterilisation cycle.
  • Printing a UDI code without an inline verification step, so a bad print is found at the customer rather than at the line.
  • Treating the tamper-evident seal as a packaging accessory rather than as part of the product identity.
  • Choosing the cheapest label stock for a small vial where the code simply does not fit at the current print resolution.

How a project runs

  1. Confirm the regulatory content. Which code, which data fields, which retention requirement – the customer’s regulatory team usually leads this.
  2. Test on the real pack and process. Printing, sterilisation, cold chain and handling, in that order.
  3. Add verification. Inline where volume justifies it, at the packing bench where it does not, with the result recorded.
  4. Lock the consumable specification. Ribbon and label approved together, with a documented change control so a substitution does not invalidate the validation.

FAQ

Can you supply a label that survives sterilisation?

Yes, with the caveat that the cycle defines the label. Ethylene oxide, gamma and autoclave place different demands on adhesive and face stock, and a label validated for one is not automatically valid for another. Send the sterilisation method and cycle parameters and we will test the construction before quoting it.

Do you support UDI code content?

We print and verify the carrier – the 2D code and human-readable data – to the content your regulatory team defines. The data structure and the registration with the competent authority remain with the manufacturer.

What is the difference between serialisation and batch coding?

Batch coding gives every unit in a batch the same lot and expiry. Serialisation gives every unit its own identifier and links it to that batch. For medicines and many devices the requirement is serialisation, which means the software and the verification step matter as much as the printer.

Can you work with our existing validated line?

Yes. Most projects add a coder or a label printer to an existing line rather than replacing it. We work to the line’s speed, mounting points and signal interface, and we document what changed so your validation team can assess the impact.